If you own a slippery enamelled cast-iron or steel bath or shower tray, then you need traXion CERAMIC, the safe, invisible and non-toxic way to make baths and showers slip-proof.
For use on enamelled steel and enamelled cast iron baths and shower trays. If you are not sure if you have a steel or cast iron bath or shower tray, use a magnet to test the material. If the magnet sticks then you need traXion CERAMIC. If the magnet does not stick to the wall of the bath or shower, then you need traXion ACRYLIC.
To apply, simply clean the surface to be treated, spray on the solution (the bottle contains enough product to treat one standard bath or shower), wait 5 minutes then rinse down, and your bath or shower will be slip-proof for years to come.
Once treated, clean the surface as normal but don't use scourers as these will reduce the effectiveness of the treatment. Repeat the treatment every few years or as necessary.
traXion ACRYLIC comes in the form of a kit that is simple to apply and is specially formulated to reduce slips and falls in acrylic, plastic, fibreglass or resin showers or baths.
Use traXion ACRYLIC on plastic, acrylic, fibreglass and resin baths and shower trays. The resultant coating is clear, shiny and rock hard with a grainy feel that provides its non-slip characteristics.
traXion ACRYLIC comes in kit form and contains everything you need to make your bath or shower slip-proof. Before starting however, make sure you have used a magnet to find out which type of material your bath or shower is made of. If the magnet sticks to the inside of the bath or shower tray then you need traXion CERAMIC. If the magnet does not stick, then you need traXion ACRYLIC.
Simply mix the components in the tray supplied, then apply the mixture using the roller provided, and allow up to 24 hours to set. Job done!
The resultant coating is clear and shiny (meaning it is suitable for any coloured bath or shower) and will give years of slip proof service. Clean as usual, but do not use abrasive powders or cloths.
Ideal for small repairs, traXion RENOVATOR is specially formulated to remove cracks and small chips from tired and ageing enamelled surfaces such as baths, shower trays and sinks.
traXion RENOVATOR is ideal for those sinks, baths and shower trays that are looking for a new lease of life. Restore your bath or kitchen sink to its original glory. Get your down and out Belfast sink back into service. Use traXion RENOVATOR to polish out hairline and problmem cracks and chips at a fraction of the cost of a complete re-enamelling service.
Simple to apply, just pour a small amount of the solution onto the cloth supplied, then rub the affected area gently, transferring the surrounding enamel over the chipped or cracked area while keeping the cloth wetted with traXion RENOVATOR solution at all times.
traXion RENOVATOR works on both white and coloured enamel surfaces. For big chips, apply enamel paint over the surface then once dry, use traXion RENOVATOR to smooth over the join.
traXion UNIVERSAL is quite simply the latest and greatest in non-slip treatments - the quick and effective solution to slippery baths, showers, floor tiles and a whole range of other mineral surfaces.
traXion UNIVERSAL can be applied to glossy tiles, polished & travertine marble, limestone, granite, porcelain tiles and terrazzo. It even works on steel, aluminium and plate glass flooring, staircases and floor lights.
traXion UNIVERSAL comes in three sizes: a 15 ml bottle which is sufficient to treat a standard bath or shower; a 30 ml bottle for bathrooms and floors measuring up to 4 m² (45 sq. ft.) and a 50 ml bottle which is sufficient to cover up to 7 m² (75 sq. ft.) of non-porous surfaces. If the surface is porous (such as in the case of marble), then two coats will be required, meaning you'll need twice as much product for the same area.
To apply, simply clean the surface to be treated, then apply the solution generously to the whole of the surface using the cloth provided, adding more solution as necessary so the whole surface remains wetted for at least 10 minutes. Allow to dry (6 to 12 hours) then test and repeat if necessary.
Once treated, the surface can be buffed to restore shine and will remain slip-proof for years to come. Clean the surface as normal but don't use scourers or abrasive floor polishers as these will remove the coating, reducing the effectiveness of the treatment.
Repeat the treatment every few years or as necessary.
After treatment there is no need to wax the floor as this too will impair the surface's slip proof properties. In hard water areas clean the floor periodically with a diluted solution of limescale remover.
Glossy ceramic floor tiles are notoriously slippery when wet.
traXion P110 is formulated to make them non slip in record time.
traXion P110 is suitable for use on glossy ceramic and vitreous ceramic floor tiles. Some loss of shine may occur in the case of very shiny tiles, so always test the solution beforehand on an inconspicuous area to determine the product's suitability.
Each 1 litre bottle is sufficient to treat between 5 and 10 m² (50 to 100 sq. ft.) of floor area, depending on the exact type of material the floor is made of.
In the case of stone (silicate) based flags and tiles, use P130 and for marble tiles and fixtures use traXion UNIVERSAL.
The solution should be applied neat, directly to the surface using a roller or a vileda floor cloth, and allowed to stand for 10 to 15 minutes before rinsing off with clean water. Test the treated surface is adequately slip-proof by wetting the treated surface and repeating the treatment if necessary.
The treated tiles will give years of non-slip service according to the traffic density.
Clean as usual, but do not use scourers or abrasive floor polishers. After treatment there is no need to wax the floor as this too will impair the surface's non-slip properties. In hard water areas clean the floor periodically with a diluted solution of limescale remover.
Available in 1 litre and 5 litre economy bottles, depending on the area to be treated, traXion P130 is specially formulated to make your floor non-slip in record time.
traXion P130 is suitable for use on most types of floor tiles and flagstones, with the exception of brilliant glazed tiles (use P110), marble tiles (use traXion UNIVERSAL) and floor coverings such as lino (contact us).
As some lightening of the colouration may occur in the case of very dark tiles, and some loss of shine may occur in the case of very shiny tiles, always test the solution beforehand on an inconspicuous area to determine the product's suitability.
The solution should be applied neat, directly to the surface using a roller or a vileda floor cloth, and allowed to stand for 10 to 15 minutes before rinsing off with clean water. Test the treated surface is adequately slip-proof by wetting the treated surface and repeating the treatment if necessary.
The treated tiles will give years of slip proof service according to the traffic density. Clean as usual, but do not use abrasive floor polishers.
After treatment there is no need to wax the floor as this too will impair the surface's non slip properties. In hard water areas clean the floor periodically with a diluted solution of limescale remover.
Are you a hotelier with slippery enamelled baths or shower trays, or an industrial with individual porcelaine showers for your employees to use? In that case you need traXion CERAMIC, the safe, invisible and non-toxic way to make baths and showers slip-proof.
For use on enamelled steel and enamelled cast iron baths and shower trays. If you are not sure if you have a steel or cast iron bath or shower tray, use a magnet to test the material. If the magnet sticks then you need traXion CERAMIC. If the magnet does not stick to the wall of the bath or shower, then you need traXion ACRYLIC.
To apply, simply clean the surface to be treated, then apply a small amount of the solution to the surface to be treated, using a cloth or roller. Wait 5 minutes then rinse down, and your bath or shower will be slip-proof for years to come.
Once treated, clean the surface as normal but don't use scourers as these will reduce the effectiveness of the treatment. Repeat the treatment every few years or as necessary.
traXion ACRYLIC comes with everything you need to carry out the treatmentto reduce slips and falls on a wide range of surface materials: plastic baths or showers, steel stairways and ladder rungs, even perspex and plate glass.
traXion ACRYLIC is an epoxy-based coating that, once cured, leaves a hard, shiny and slightly grainy clear coating that reduces slips and falls dramatically. The resultant coating is UV-resistant and is designed to provide a minimum useful life of at least 3 year after which the coating can be reapplied.
traXion ACRYLIC comes with everything you need to make your problem areas slip-proof.
Clean the surfaces using isopropanol or similar solvent, then dry and mask off the areas to be coated using standard masking tape. Mix the components in the tray supplied, then apply the mixture using the roller provided. Remove the masking tape after 30 minutes or so, then allow up to 24 hours to set.
The resultant coating is clear and shiny (meaning it is suitable for any coloured surface) and should be cleaned as usual, though abrasive powders or cloths or wire brushed should be avoided.
Ideal for a large number of small repairs, our economy version of traXion RENOVATOR is specially formulated to remove cracks and small chips from tired and ageing enamelled surfaces such as baths, shower trays and sinks.
traXion RENOVATOR is ideal for sinks, baths and shower trays that look tired and in need of a new lease of life. Restore your bath or kitchen sink to its original glory. Belfast and similar sinks back can be easily brought back into service by using traXion RENOVATOR to polish out hairline and problem cracks and chips at a fraction of the cost of a complete re-enamelling service.
Simple to apply, just pour a small amount of the solution onto the cloth supplied, then rub the affected area gently, transferring the surrounding enamel over the chipped or cracked area while keeping the cloth wetted with traXion RENOVATOR solution at all times.
traXion RENOVATOR works on both white and coloured enamel surfaces. For big chips, apply enamel paint over the surface then once dry, use traXion RENOVATOR to smooth over the join.
traXion UNIVERSAL is ideal for treating polished and travertine marble, polished slate, gritstone and sandstone and a whole range of other surfaces without altering their appearance.
traXion UNIVERSAL is a specially formulated coating that can be applied to a whole range of materials including glossy tiles, polished & travertine marble, limestone, granite, porcelain tiles and terrazzo. It even works on steel, aluminium and plate glass flooring, staircases and floor lights.
One bottle is sufficient to cover up to 28 m² (300 sq. ft.) of non-porous surfaces and up to 14 m² (150 sq. ft.) of porous surfaces such as marble.
Test this solution first on a small inconspicuous area for suitability. To apply, simply clean the surface to be treated, then apply the solution generously to the whole of the surface using the cloth provided, adding more solution sparingly and as necessary so the whole surface remains wetted for at least 10 minutes. Allow to dry (6 to 12 hours) then test and repeat if necessary.
Once treated, the surface can be buffed to restore shine and will remain slip-proof for years to come. Clean the surface as normal but don't use scourers or abrasive floor polishers as these will remove the coating, reducing the effectiveness of the treatment.
Repeat the treatment every few years or as necessary.
After treatment there is no need to wax the floor as this too will impair the surface's non slip properties. In hard water areas clean the floor periodically with a diluted solution of limescale remover.
Glossy ceramic floor tiles are notoriously slippery when wet.
traXion P110 is formulated to make them non-slip in record time.
traXion P110 is suitable for use on vitreous and glossy ceramic floor tiles. It is quick and easy to apply and the treatment is virtually instantaneous, meaning there is very little down time compared to coatings.
Each 5 litre bottle is sufficient to treat between 25 and 50 m² (250 to 500 sq. ft.) of floor area, depending on the exact type of material the floor is made of.
Retreatment (every few years) is equally simple; there is nothing to remove, you just go back over the treated floor with more P110 to restore its slip-proof qualities.
As some lightening of the colouration may occur in the case of very dark tiles, and some loss of shine may occur in the case of very shiny tiles, always test the solution beforehand on an inconspicuous area to determine the product's suitability.
The solution should be applied neat, directly to the surface using a roller or a vileda floor cloth, and allowed to stand for 10 to 15 minutes before rinsing off with clean water. Test the treated surface is adequately slip-proof by wetting the treated surface and repeating the treatment if necessary.
The treated tiles will give years of slip proof service according to the traffic density.
Clean as usual, but do not use scourers or abrasive floor polishers. After treatment there is no need to wax the floor as this too will impair the surface's non slip properties.
In hard water areas clean the floor periodically with a diluted solution of limescale remover.
In areas that are exposed to oils, fats, creams or lotions (such as in the case of swimming pools, spas, saunas, kitchens and areas where food is processed, degrease frequently using an industrial-grade degreasing agent and industrial wet & dry vacuum cleaner.
Available in 1 litre and 5 litre economy bottles, depending on the area to be treated, traXion P130 is specially formulated to make your floor non-slip in record time.
traXion P130 is suitable for use on most types of floor tiles and flagstones, with the exception of brilliant glazed tiles (use P110) and marble tiles (use traXion UNIVERSAL).
It is quick and easy to apply and the treatment is virtually instantaneous, meaning there is very little down time compared to coatings.
Retreatment (every few years) is equally simple; there is nothing to remove, you just go back over the treated floor with more P110 to restore its slip-proof qualities.
Each 5 litre bottle is sufficient to treat between 25 and 50 m² (250 to 500 sq. ft.) of floor area, depending on the exact type of material the floor is made of.
As some lightening of the colouration may occur in the case of very dark tiles, and some loss of shine may occur in the case of very shiny tiles, always test the solution beforehand on an inconspicuous area to determine the product's suitability.
The solution should be applied neat, directly to the surface using a roller or a vileda floor cloth, and allowed to stand for 10 to 15 minutes before rinsing off with clean water. Test the treated surface is adequately slip-proof by wetting the treated surface and repeating the treatment if necessary.
The treated tiles will give years of non slip service according to the traffic density. Clean as usual, but do not use abrasive floor polishers.
After treatment there is no need to wax the floor as this too will impair the surface's non-slip properties.
In hard water areas clean the floor periodically with a diluted solution of limescale remover.
In areas that are exposed to oils, fats, creams or lotions (such as in the case of swimming pools, spas, saunas, kitchens and areas where food is processed, degrease frequently using an industrial-grade degreasing agent and industrial wet & dry vacuum cleaner.
traXion UNIVERSAL is quite simply the latest and greatest in non-slip treatments - the quick and effective solution to slippery baths, showers, floor tiles and a whole range of other surfaces.
traXion UNIVERSAL can be applied to glossy tiles, polished & travertine marble, limestone, granite, porcelain tiles and terrazzo. It even works on steel, aluminium and plate glass flooring, staircases and floor lights.
One bottle is sufficient to cover up to 28 m² (300 sq. ft.) of non-porous surfaces and up to 14 m² (150 sq. ft.) of porous surfaces such as marble.
Before using this solution, first test it on a small inconspicuous area for suitability. To apply, simply clean and degrease the surface to be treated, then apply the solution generously to the whole of the surface using the cloth provided, adding more solution as necessary so the whole surface remains wetted for at least 10 minutes. Allow to dry (6 to 12 hours) then test and repeat if necessary.
Once treated, the surface can be buffed to restore shine and will remain slip-proof for years to come. Clean the surface as normal but don't use scourers or abrasive floor polishers as these will remove the coating, reducing the effectiveness of the treatment.
Repeat the treatment every few years or as necessary.
After treatment there is no need to wax the floor as this too will impair the surface's non slip properties. In hard water areas clean the floor periodically with a diluted solution of limescale remover.
Glossy ceramic floor tiles are notoriously slippery when wet.
traXion P110 is specially formulated to make them non-slip with the minimum of fuss.
traXion P110 is suitable for use on glossy ceramic and vitreous ceramic floor tiles.
In the case of stone (silicate) based flags and tiles, use P130), for marble tiles use traXion UNIVERSAL, and for floor coverings such as lino, contact us.
Each 5 litre bottle is sufficient to treat between 25 and 50 m² (250 to 500 sq. ft.) of floor area, depending on the exact type of material the floor is made of.
Some loss of shine may occur in the case of very shiny tiles, so always test the solution beforehand on an inconspicuous area to determine the product's suitability.
The solution should be applied neat, directly to the surface using a roller or a vileda floor cloth, and allowed to stand for 10 to 15 minutes before rinsing off with clean water.
Test the treated surface is adequately slip-proof by wetting the treated surface and repeating the treatment if necessary.
The treated tiles will give years of non slip service according to the traffic density.
Clean as usual, but do not use scourers or abrasive floor polishers. After treatment there is no need to wax the floor as this too will impair the surface's non slip properties.
In hard water areas clean the floor periodically with a diluted solution of limescale remover.In areas that are exposed to oils, fats, creams or lotions (such as in the case of swimming pools, spas, saunas, kitchens and areas where food is processed, degrease frequently using an industrial-grade degreasing agent and industrial wet & dry vacuum cleaner.
traXion P130 is not a coating but a specially formulated treatment that renders sandstone, gritstone, slate and other silica-based tiles and flagstones non-slip in record time for three years or more.
traXion P130 is suitable for use on most types of floor tiles and flags, with the exception of brilliant glazed tiles (use P110), marble tiles (use traXion UNIVERSAL) and floor coverings such as lino (contact us).
Each 5 litre bottle is sufficient to treat between 25 and 50 m² (250 to 500 sq. ft.) of floor area, depending on the exact type of material the treated surface is made of.
As some lightening of the colouration may occur in the case of very dark tiles, and some loss of shine may occur in the case of very shiny tiles, always test the solution beforehand on an inconspicuous area to determine the product's suitability.
The solution should be applied neat, directly to the previously cleaned surface using a paint roller or vileda-type floor cloth, and allowed to stand for 10 to 15 minutes before rinsing off with clean water.
Test the treated surface is adequately slip-proof by wetting the treated surface and repeating the treatment if necessary.
The treated tiles will give years of non slip service according to the traffic density. Clean as usual, but do not use abrasive floor polishers. Retreat as necessary following the exact same procedure.
After treatment there is no need to wax the floor as this too will impair the surface's non-slip properties.
In hard water areas clean the floor periodically with a diluted solution of limescale remover.
In areas that are exposed to oils, fats, creams or lotions (such as in the case of swimming pools, spas, saunas, kitchens and areas where food is processed, degrease frequently using an industrial-grade degreasing agent and industrial wet & dry vacuum cleaner.
The traXion solutions range of non-slip products are sold throughout Western Europe and farther afield including the USA, Canada, Central America and North Africa. In the UK and Ireland, northern and eastern Europe, the distribution of traXion products is handled by NTS Europe which has offices in both the UK and France.
We are sure that everyone would agree: the traXion solutions website had not changed since the launch of its range of non-slip products in the UK and was in dire need of a facelift. Well, here's the result. Why not drop us a line and let us know what you think, what we should change and what we should add? We're all ears!